电磁脉冲焊接用真空触发开关工作特性及影响因素

李成祥; 陈丹; 杜建; 廖志刚; 周言

doi:10.11884/HPLPB202436.240345

电磁脉冲焊接用真空触发开关工作特性及影响因素

doi: 10.11884/HPLPB202436.240345

李成祥^1,,
陈丹¹,
杜建^{1, 2},
廖志刚^{1, 2},
周言^1, ,

1.
输变电装备技术全国重点实验室（重庆大学电气工程学院），重庆 400044
2.
国网重庆市电力公司永川供电分公司，重庆 402160

基金项目: 国家自然科学基金项目(52207148); 重庆市自然科学基金项目(CSTB2022NSCQ-MSX1238)

详细信息

作者简介:
李成祥，lichengxiang@cqu.edu.cn

通讯作者:
周　言，zhouyan1992@cqu.edu.cn。

中图分类号: TM89
计量
- 文章访问数: 159
- HTML全文浏览量: 46
- PDF下载量: 17
- 被引次数: 0
出版历程
- 收稿日期: 2024-09-27
- 修回日期: 2024-10-25
- 录用日期: 2024-10-18
- 网络出版日期: 2024-10-28
- 刊出日期: 2024-11-01

Operational characteristics and effect factors on the triggered vacuum switch for electromagnetic pulse welding

Li Chengxiang^1
,,
Chen Dan¹,
Du Jian^{1, 2},
Liao Zhigang^{1, 2},
Zhou Yan^{1
, ,}

1.
State Key Laboratory of Power Transmission Equipment Technology, School of Electrical Engineering, Chongqing University, Chongqing 400044, China
2.
State Grid Chongqing Electric Power Company Yongchuan Power Supply Branch, Chongqing 402160, China

摘要

摘要: 电磁脉冲焊接是脉冲功率技术在材料加工中的应用之一，常采用真空触发开关（TVS）作为放电开关。根据电磁脉冲焊接过程特征，针对课题组所用的ZKTC国产新型TVS，详细探究了ZKTC在其触发阶段、导通阶段与初次放电阶段的工作特性。通过仿真研究了电路参数对ZKTC工作过程的影响；研制了Marx电路与脉冲变压器结合的触发装置，脉宽0～10 μs可调、幅值0～20 kV可调，基于ZKTC搭建了放电能量为27 kJ的脉冲大电流发生器测试平台并开展实验分析。结果表明，触发信号的电压幅值与上升前沿均会显著影响ZKTC触发过程；放电主回路工作电压幅值会影响ZKTC导通阶段中带电粒子的定向迁移速率与放电电流幅值，改变开关放电回路的参数并加快电压下降速度，从而对导通阶段和放电阶段产生明显影响。
- 真空触发开关 /
- 电磁脉冲焊接 /
- 导通特性 /
- 触发装置
Abstract: Electromagnetic pulse welding (EMPW) is a key application of pulsed power technology in materials processing, where triggered vacuum switch (TVS) is frequently employed as discharge switch. Based on the specific behavior of the EMPW process, this paper presents a detailed investigation into the operational characteristics of a new domestically produced TVS, named ZKTC. The study focuses on the switch's behavior during the triggering, conducting, and initial discharging stages. The effects of circuit parameters on ZKTC's operation were analyzed through simulations. A trigger device combining a Marx circuit and a pulse transformer was developed, featuring adjustable pulse widths (0–10 μs) and adjustable voltage amplitudes (0–20 kV). Based on ZKTC, a high-current pulsed generator testing platform with a discharge energy of 27 kJ was constructed to perform experimental analyses. The results indicate that the voltage amplitude and rising edge of the trigger signal significantly influence the ZKTC triggering process. While the working voltage amplitude of the main discharge circuit impacts the directional migration rate of charged particles and the discharge current during the conducting stage, modifying the parameters of the switch discharge circuit and accelerating the voltage drop rate. This, in turn, has a significant effect on both the conducting and discharging stages.
- triggered vacuum switch /
- electromagnetic pulse welding /
- conduction characteristics /
- trigger device

HTML全文

图 1 TVS工作过程

Figure 1. Stages of TVS operation

下载: 全尺寸图片幻灯片

图 2 触发阶段仿真结果

Figure 2. Simulation results of the triggering stage

下载: 全尺寸图片幻灯片

图 3 导通阶段电路模型

Figure 3. Circuit model of conducting stage

下载: 全尺寸图片幻灯片

图 4 初次放电阶段电路模型与PSpice仿真模型

Figure 4. Circuit model and PSpice simulation model of initial discharging stage

下载: 全尺寸图片幻灯片

图 5 初次放电阶段仿真结果

Figure 5. Simulation results of initial discharging stage

下载: 全尺寸图片幻灯片

图 6 ZKTC实物图

Figure 6. Physical diagram of ZKTC

下载: 全尺寸图片幻灯片

图 7 触发装置及其输出波形

Figure 7. Trigger device and its output waveform

下载: 全尺寸图片幻灯片

图 8 ZKTC测试平台及其测试波形

Figure 8. The test platform of the ZKTC and its test waveform

下载: 全尺寸图片幻灯片

图 9 触发电压对ZKTC各工作阶段的影响

Figure 9. Effects of trigger voltage on various operational stages of ZKTC

下载: 全尺寸图片幻灯片

图 10 触发信号脉冲宽度对ZKTC导通阶段t₂的影响

Figure 10. Effect of trigger signal pulse width on the conducting stage t₂ of ZKTC

下载: 全尺寸图片幻灯片

图 11 工作电压对ZKTC工作过程中各工作阶段的影响

Figure 11. Effect of working voltage on various operational stages of ZKTC operational process

下载: 全尺寸图片幻灯片

参考文献(25)

[1]	李成祥, 王淑慧, 吴浩, 等. 脉冲参数对激活动作电位强度阈值影响的仿真研究[J]. 高电压技术, 2021, 47(4):1451-1460 Li Chengxiang, Wang Shuhui, Wu Hao, et al. Simulation study on the effect of pulse parameters on intensity threshold for action potential activation[J]. High Voltage Engineering, 2021, 47(4): 1451-1460
[2]	Kovalchuk B M, Kharlov A V, Vizir V A, et al. High-voltage pulsed generator for dynamic fragmentation of rocks[J]. Review of Scientific Instruments, 2010, 81: 103506. doi: 10.1063/1.3497307
[3]	Psyk V, Scheffler C, Linnemann M, et al. Manufacturing of hybrid aluminum copper joints by electromagnetic pulse welding - Identification of quantitative process windows[J]. AIP Conference Proceedings, 2017, 1896: 110001.
[4]	Li Chengxiang, Kou Pengfei, Dai Ming, et al. Separation of lithium-ion battery cathode active materials by vaporizing the current collector with pulsed current[J]. IEEE Transactions on Plasma Science, 2024, 52(2): 374-383. doi: 10.1109/TPS.2024.3364241
[5]	Zhou Yan, Tan Jianwen, Yao Chenguo, et al. Finite-element simulation and experiments on plastic heating in the process of electromagnetic pulse forming[J]. IEEE Transactions on Plasma Science, 2018, 46(10): 3427-3437. doi: 10.1109/TPS.2018.2825650
[6]	Guo Xiaoqiang, Zheng Dongpo, Blaabjerg F. Power electronic pulse generators for water treatment application: a review[J]. IEEE Transactions on Power Electronics, 2020, 35(10): 10285-10305. doi: 10.1109/TPEL.2020.2976145
[7]	江伟华. 高重复频率脉冲功率技术及其应用: (4)半导体开关的特长与局限性[J]. 强激光与粒子束, 2013, 25(3):537-543 doi: 10.3788/HPLPB20132503.0537 Jiang Weihua. Repetition rate pulsed power technology and its applications: (iv) advantage and limitation of semiconductor switches[J]. High Power Laser and Particle Beams, 2013, 25(3): 537-543 doi: 10.3788/HPLPB20132503.0537
[8]	王磊, 章程, 高迎慧, 等. 晶闸管串联开关及同步触发系统研制[J]. 强激光与粒子束, 2015, 27:115001 doi: 10.11884/HPLPB201527.115001 Wang Lei, Zhang Cheng, Gao Yinghui, et al. Design of series-connected thyristor switch and synchronous triggering circuit[J]. High Power Laser and Particle Beams, 2015, 27: 115001 doi: 10.11884/HPLPB201527.115001
[9]	Kumar R, Sahoo S, Sarkar B, et al. Development of electromagnetic welding facility of flat plates for nuclear industry[J]. Journal of Physics: Conference Series, 2017, 823: 012039. doi: 10.1088/1742-6596/823/1/012039
[10]	Zhang Xin, Fan Xingming, Huang Zhichao, et al. Triggering characteristic of TVS and its application research in synthetic making test for high voltage circuit-breakers[C]//Proceedings of the 25th International Symposium on Discharges and Electrical Insulation in Vacuum. 2013.
[11]	廖敏夫, 董华庆, 陈占清, 等. 不同电极激光触发真空开关高频开断能力研究[J]. 高电压技术, 2020, 46(7):2578-2585 Liao Minfu, Dong Huaqing, Chen Zhanqing, et al. Research on high-frequency interruption capacity of LTVS with different electrodes[J]. High Voltage Engineering, 2020, 46(7): 2578-2585
[12]	廖敏夫, 邹积岩, 段雄英, 等. 高性能真空触发开关技术的研究综述[J]. 高压电器, 2006, 42(1):51-54 doi: 10.3969/j.issn.1001-1609.2006.01.016 Liao Minfu, Zou Jiyan, Duan Xiongying, et al. Overview on techniques of high-performance triggered vacuum switch[J]. High Voltage Apparatus, 2006, 42(1): 51-54 doi: 10.3969/j.issn.1001-1609.2006.01.016
[13]	Akhmetgareev M R, Alferov D F, Bunin R A, et al. Triggered vacuum switch with an axial magnetic field[J]. IEEE Transactions on Plasma Science, 2013, 41(8): 2154-2159. doi: 10.1109/TPS.2013.2239664
[14]	Wang Yanzhao, Dai Ling, Lin Fuchang, et al. Optimization of a triggered vacuum switch with multirod electrodes system[J]. IEEE Transactions on Plasma Science, 2014, 42(1): 162-167. doi: 10.1109/TPS.2013.2289379
[15]	Park W H, Kong H S, An S H, et al. Research on the characteristics of a triggered vacuum switch with a surface flashover trigger device[J]. Journal of the Korean Physical Society, 2020, 77(10): 919-923. doi: 10.3938/jkps.77.919
[16]	卢彪, 彭太平, 言杰, 等. 一种基于吸气电极的新型真空触发开关[J]. 强激光与粒子束, 2021, 33:055003 doi: 10.11884/HPLPB202133.210014 Lu Biao, Peng Taiping, Yan Jie, et al. New type of triggered vacuum switch based on gas-breathing electrode[J]. High Power Laser and Particle Beams, 2021, 33: 055003 doi: 10.11884/HPLPB202133.210014
[17]	Wu Hao, He Zhenghao, Wang Lei, et al. Effect of the trigger circuit on delay characteristics of a triggered vacuum switch with a six-gap rod electrode system[J]. IEEE Transactions on Plasma Science, 2011, 39(1): 335-341. doi: 10.1109/TPS.2010.2052836
[18]	李化, 龙兆芝, 林福昌, 等. 多棒极型触发真空开关触发特性[J]. 电工技术学报, 2009, 24(11):61-67 doi: 10.3321/j.issn:1000-6753.2009.11.010 Li Hua, Long Zhaozhi, Lin Fuchang, et al. Triggering characteristics of multi-electrode type triggered vacuum switch[J]. Transactions of China Electrotechnical Society, 2009, 24(11): 61-67 doi: 10.3321/j.issn:1000-6753.2009.11.010
[19]	Zhou Zhengyang, Dai Ling, Nan Jing, et al. Operational characteristics of a surface breakdown triggered vacuum switch with six gap rod electrode system[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2011, 18(4): 997-1002. doi: 10.1109/TDEI.2011.5976087
[20]	Cai Li, Li L, Liu Yunlong, et al. Analysis of breakdown mechanism in trigatron switches[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2013, 20(4): 1069-1075. doi: 10.1109/TDEI.2013.6571419
[21]	Kore S D, Dhanesh P, Kulkarni S V, et al. Numerical modeling of electromagnetic welding[J]. International Journal of Applied Electromagnetics and Mechanics, 2010, 32(1): 1-19. doi: 10.3233/JAE-2010-1062
[22]	Zhou Yan, Zhou Zehong, Yao Chenguo, et al. Fast-rise-time trigger source based on solid-state switch and pulse transformer for triggered vacuum switch[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2017, 24(4): 2105-2114. doi: 10.1109/TDEI.2017.006345
[23]	Wang Yanzhao, Lin Fuchang, Dai Ling, et al. Research on time delay and lifetime characteristics of triggered vacuum switch with multirod system[J]. IEEE Transactions on Plasma Science, 2013, 41(5): 1307-1312. doi: 10.1109/TPS.2013.2248393
[24]	王昌金. 基于Marx和LTD拓扑的全固态复合模式脉冲源的研制[D]. 重庆: 重庆大学, 2018 Wang Changjin. The development of all solid-state mixed pulse generator based on Marx and LTD topologies[D]. Chongqing: Chongqing University, 2018
[25]	张亚舟. 脉冲功率开关在电磁轨道炮电容储能电源中的应用与实验研究[D]. 南京: 南京理工大学, 2018 Zhang Yazhou. The application and experiment research on pulsed power switch of capacitor-based power supply in electromagnetic railgun[D]. Nanjing: Nanjing University of Science & Technology, 2018