Investigation on charge-discharge properties of glass-ceramic based pulse forming lines

Zhang Qingmeng; Luan Chongbiao; Tang Qun; Li Hongtao

doi:10.11884/HPLPB201830.170329

Volume 30 Issue 2

Feb. 2018

Turn off MathJax

Article Contents

Article Navigation > High Power Laser and Particle Beams > 2018 > 30(2): 025008

Zhang Qingmeng, Luan Chongbiao, Tang Qun, et al. Investigation on charge-discharge properties of glass-ceramic based pulse forming lines[J]. High Power Laser and Particle Beams, 2018, 30: 025008. doi: 10.11884/HPLPB201830.170329

Citation:

Zhang Qingmeng, Luan Chongbiao, Tang Qun, et al. Investigation on charge-discharge properties of glass-ceramic based pulse forming lines[J]. High Power Laser and Particle Beams, 2018, 30: 025008. doi: 10.11884/HPLPB201830.170329

Citation:

PDF( 2522 KB)

Investigation on charge-discharge properties of glass-ceramic based pulse forming lines

doi: 10.11884/HPLPB201830.170329

1.
Advanced Electronic Materials Institute, General Research Institute for Nonferrous Metals, Beijing 100088, China
2.
Institute of Fluid Physics, CAEP, P. O. Box 919-988, Mianyang 621900, China

Received Date: 2017-08-27
Rev Recd Date: 2017-10-30
Publish Date: 2018-02-15

Abstract

Abstract

Large-sized (Pb, Sr)Nb₂O₆-NaNbO₃-SiO₂ glass ceramic plate was fabricated via melt-quenching followed by controlled crystallization. Its dielectric properties and charge-discharge properties were investigated. The results show that the dielectric constant is about 340 and has good temperature and voltage stability. The output pulse width of glass-ceramic pulse forming line is about 89 ns, and shows good flatness and steep front edge. The charge-discharge lifetime of pulse forming line is larger than one million times under the charge voltage of 19 kV, discharge current of 4 kA and operating frequency of 1 kHz.
- glass ceramic,
- solid-state pulse forming line,
- dielectric properties,
- charge-discharge properties

FullText(HTML)

References(11)

References

[1]	Ness R, Melcher P, Ferguson G, et al. A decade of solid state pulsed power development at Cymer Inc[C]//International Power Modulator Symposium. 2005: 228-233.
[2]	Jiang Weihua, Oshima N, Yokoo T, et al. Development of repetitive pulsed power generators using power semiconductor devices[C]//Pulsed Power Conference. 2005: 1167-1172.
[3]	Redondo L M, Pereira M T. Repetitive all solid-state pulse Marx type generator with energy recovery clamp circuit for inductive loads[C]//16th IEEE International Pulsed Power Conference. 2007: 711-715.
[4]	Domonkos M T, Turchi P J, Parker J V, et al. A ceramic loaded polymer Blumlein pulser for compact, rep-rated pulsed power applications[C]//15th IEEE International Pulsed Power Conference. 2005: 1322-1325.
[5]	Surender K S, Deb P, Shukla R, et al. Compact pulse forming line using barium titanate ceramic material[J]. Rev Sci Instrum, 2011, 82: 115102.
[6]	Xia L, Zhang H, Shi J, et al. A compact, portable pulse forming line[J]. Rev Sci Instrum, 2008, 79: 086113. doi: 10.1063/1.2970945
[7]	Wang Songsong, Shu Ting, Yang Hanwu. A modularized pulse forming line using glass-ceramic slabs[J]. Rev Sci Instrum, 2012, 83: 084703. doi: 10.1063/1.4740522
[8]	Zhang Qingmeng, Li Chang, Liu Hongwei, et al. Discharged energy properties of SrO-PbO-Na₂O-Nb₂O₅-SiO₂[J]. Journal of the American Ceramic Society, 2015, 98: 366-369. doi: 10.1111/jace.13390
[9]	Tian Yuming, Zhou Yi, Du Jun. Preparation and dielectrics characterization of lead-free niobate glass-ceramic composites added with Lu₂O₃[J]. Journal of the American Ceramic Society, 2014, 97: 2353-2356. doi: 10.1111/jace.13010
[10]	Chen G H, Liu T Y, Yuan C L, et al. Effect of BaF₂ addition on crystallization kinetics and electrical properties of BaO-SrO-Nb₂O₅-B₂O₃-SiO₂ glass-ceramics[J]. Journal of Non-Crystalline Solids, 2013, 378: 241-246.
[11]	李洪涛, 刘金锋, 袁建强, 等. 大功率固态脉冲形成线研究进展[J]. 强激光与粒子束, 2011, 23(11): 2906-2910. http://www.hplpb.com.cn/article/id/5421 Li Hongtao, Liu Jinfeng, Yuan Jianqiang. Development progress of high-power solid-state pulse forming lines. High Power Laser and Particle Beams, 2011, 23(11): 2906-2910 http://www.hplpb.com.cn/article/id/5421