Evolution of explosion plume on the rear surface of silica elements in nanosecond laser damaging

Yuan Hang; Liang Lingxi; Li Yuxin; Dan Ziqiang; Zhu Chengyu

doi:10.11884/HPLPB202335.220395

Volume 35 Issue 6

May 2023

Turn off MathJax

Article Contents

Abstract

References

Article Navigation > High Power Laser and Particle Beams > 2023 > 35(6): 061002

Wu Min’gan, Liu Yi, Lin Fuchang, et al. Characteristics analysis of electrohydraulic shockwave[J]. High Power Laser and Particle Beams, 2020, 32: 045002. doi: 10.11884/HPLPB202032.190356

Citation:

Yuan Hang, Liang Lingxi, Li Yuxin, et al. Evolution of explosion plume on the rear surface of silica elements in nanosecond laser damaging[J]. High Power Laser and Particle Beams, 2023, 35: 061002. doi: 10.11884/HPLPB202335.220395

Wu Min’gan, Liu Yi, Lin Fuchang, et al. Characteristics analysis of electrohydraulic shockwave[J]. High Power Laser and Particle Beams, 2020, 32: 045002. doi: 10.11884/HPLPB202032.190356

Citation:

PDF( 20711 KB)

Evolution of explosion plume on the rear surface of silica elements in nanosecond laser damaging

doi: 10.11884/HPLPB202335.220395

Yuan Hang^1
,,
Liang Lingxi^{1, 2},
Li Yuxin¹,
Dan Ziqiang¹,
Zhu Chengyu^{1
,
,}

1.
Key Laboratory of Tunable Laser, Harbin Institute of Technology, Harbin 150001, China
2.
Laser Fusion Research Center, CAEP, Mianyang 621900, China

Received Date: 2022-12-28
Accepted Date: 2023-02-22
Rev Recd Date: 2023-03-15

Available Online: 2023-03-24

Publish Date: 2023-05-06

Abstract

Abstract

The study of UV laser induced damage dynamics is the key to exploring correlating evolution of optical elements’ microstructure and macroscopic properties. In optical elements damage process on the rear surface, the laser energy deposition causes the material to explode with high pressure and high temperature to break through the rear surface, and it is accompanied with explosion plume and jet particles. The explosion plume is greatly affected by the initial laser energy deposition. The study of the explosion plume can help a lot in analyzing the material state change and response mechanism at the initial stage of damage. In this paper, explosion plume on the rear surface is investigated using a two-color interferometric time-resolved side-viewed imaging system. Assisted with the observation of the collected ejection, the material species, distributions and thermodynamic behaviors of ejections are presented. Based on findings, the key transition nodes of the response behaviors during laser induced damage formation are captured and the temporal evolvement of plume is described.
- optical elements damage,
- fused silica,
- explosion plume,
- particle jet,
- damage dynamics

FullText(HTML)

References(20)

References

[1]	Spaeth M L, Wegner P J, Suratwala T I, et al. Optics recycle loop strategy for NIF operations above UV laser-induced damage threshold[J]. Fusion Science and Technology, 2016, 69(1): 265-294. doi: 10.13182/FST15-119
[2]	Chambonneau M, Lamaignère L. Multi-wavelength growth of nanosecond laser-induced surface damage on fused silica gratings[J]. Scientific Reports, 2018, 8(1): 891. doi: 10.1038/s41598-017-18957-9
[3]	Negres R A, Cross D A, Liao Z M, et al. Growth model for laser-induced damage on the exit surface of fused silica under UV, ns laser irradiation[J]. Optics Express, 2014, 22(4): 3824-3844. doi: 10.1364/OE.22.003824
[4]	Negres R A, Norton M A, Cross D A, et al. Growth behavior of laser-induced damage on fused silica optics under UV, ns laser irradiation[J]. Optics Express, 2010, 18(19): 19966-19976. doi: 10.1364/OE.18.019966
[5]	Laurence T A, Negres R A, Ly S, et al. Role of defects in laser-induced modifications of silica coatings and fused silica using picosecond pulses at 1053 nm: II. Scaling laws and the density of precursors[J]. Optics Express, 2017, 25(13): 15381-15401. doi: 10.1364/OE.25.015381
[6]	Negres R A, Raman R N, Bude J D, et al. Dynamics of transient absorption in bulk DKDP crystals following laser energy deposition[J]. Optics Express, 2012, 20(18): 20447-20458. doi: 10.1364/OE.20.020447
[7]	Raman R N, Negres R A, Demos S G. Kinetics of ejected particles during breakdown in fused silica by nanosecond laser pulses[J]. Applied Physics Letters, 2011, 98: 051901. doi: 10.1063/1.3549193
[8]	Demos S G, Negres R A, Raman R N, et al. Material response during nanosecond laser induced breakdown inside of the exit surface of fused silica[J]. Laser & Photonics Reviews, 2013, 7(3): 444-452.
[9]	Demos S G, Negres R A, Raman R N, et al. Relaxation dynamics of nanosecond laser superheated material in dielectrics[J]. Optica, 2015, 2(8): 765-772. doi: 10.1364/OPTICA.2.000765
[10]	Kanitz A, Kalus M R, Gurevich E L, et al. Review on experimental and theoretical investigations of the early stage, femtoseconds to microseconds processes during laser ablation in liquid-phase for the synthesis of colloidal nanoparticles[J]. Plasma Sources Science and Technology, 2019, 28: 103001. doi: 10.1088/1361-6595/ab3dbe
[11]	赵元安, 邵建达, 刘晓凤, 等. 光学元件的激光损伤问题[J]. 强激光与粒子束, 2022, 34:011004 doi: 10.11884/HPLPB202234.210331 Zhao Yuan’an, Shao Jianda, Liu Xiaofeng, et al. Tracking and understanding laser damage events in optics[J]. High Power Laser and Particle Beams, 2022, 34: 011004 doi: 10.11884/HPLPB202234.210331
[12]	杨李茗, 黄进, 刘红婕, 等. 熔石英元件紫外脉冲激光辐照损伤特性研究进展综述[J]. 光学学报, 2022, 42:1714004 doi: 10.3788/AOS202242.1714004 Yang Liming, Huang Jin, Liu Hongjie, et al. Review of research progress on damage characteristics of fused silica optics under ultraviolet pulsed laser irradiation[J]. Acta Optica Sinica, 2022, 42: 1714004 doi: 10.3788/AOS202242.1714004
[13]	Huang Jin, Liu Hongjie, Wang Fengrui, et al. Influence of bulk defects on bulk damage performance of fused silica optics at 355 nm nanosecond pulse laser[J]. Optics Express, 2017, 25(26): 33416-33428. doi: 10.1364/OE.25.033416
[14]	郑万国, 祖小涛, 袁晓东, 等. 高功率激光装置的负载能力及其相关物理问题[M]. 北京: 科学出版社, 2014 Zheng Wanguo, Zu Xiaotao, Yuan Xiaodong, et al. Damage resistance and physical problems of high power laser facilities[M]. Beijing: Science Press, 2014
[15]	Demos S G, Negres R A, Rubenchik A M. Dynamics of the plume containing nanometric-sized particles ejected into the atmospheric air following laser-induced breakdown on the exit surface of a CaF₂ optical window[J]. Applied Physics Letters, 2014, 104: 031603. doi: 10.1063/1.4862815
[16]	Nguyen V H, Kalal M, Suk H, et al. Interferometric analysis of sub-nanosecond laser-induced optical breakdown dynamics in the bulk of fused-silica glass[J]. Optics Express, 2018, 26(12): 14999-15008. doi: 10.1364/OE.26.014999
[17]	Demos S G, Raman R N, Negres R A. Time-resolved imaging of processes associated with exit-surface damage growth in fused silica following exposure to nanosecond laser pulses[J]. Optics Express, 2013, 21(4): 4875-4888. doi: 10.1364/OE.21.004875
[18]	Peng Ge, Zhang Peng, Dong Zhe, et al. Spatial sputtering of fused silica after a laser-induced exploding caused by a 355 nm nd: YAG laser[J]. Frontiers in Physics, 2022, 10: 980249. doi: 10.3389/fphy.2022.980249
[19]	Bude J, Guss G, Matthews M, et al. The effect of lattice temperature on surface damage in fused silica optics[C]//Proceedings of SPIE 6270, Laser-induced Damage in Optical Materials. 2007.
[20]	Zhu Chengyu, Liang Lingxi, Yuan Hang, et al. Investigation of stress wave and damage morphology growth generated by laser-induced damage on rear surface of fused silica[J]. Optics Express, 2020, 28(3): 3942-3951. doi: 10.1364/OE.384036

Relative Articles

[1]	Sun Zikuan, Qiu Junting, Zheng Lisheng, Xie Xiaozheng, Zhang Zijian. Design of digital twin-based control system for loading and unloading of proton beam irradiated thorium target[J]. High Power Laser and Particle Beams, 2025, 37(2): 024002. doi: 10.11884/HPLPB202537.240255
[2]	Wan Zhenbo, Ding Weidong. Influence analysis of cascading failure in linear transformer driver caused by group prefire[J]. High Power Laser and Particle Beams, 2024, 36(7): 075003. doi: 10.11884/HPLPB202436.240063
[3]	Han Xiaodong, Liu Donge, Xu Zhe, Zhang Ruifeng, Li Shilong, Zhou Ruihuai, Cong Yan. Design and implementation of linear injector timing system for 300 MeV proton and heavy ion accelerator[J]. High Power Laser and Particle Beams, 2024, 36(8): 084003. doi: 10.11884/HPLPB202436.240041
[4]	Ma Liehua, Chen Shuang, Li Hongtao, Peng Xusheng, Zhang Botao, Li Bo, Wang Cheng, Ai Jie. Engineering reliability design and improvement for pulsed neutron scintillation detector[J]. High Power Laser and Particle Beams, 2023, 35(11): 119002. doi: 10.11884/HPLPB202335.230130
[5]	Huang Zhanchang, Zhang Chengjun, Chen Jinchuan, Yang Jianlun, Li Linbo, You Haibo, Wang Dongming, You Wenhao, He Chao, Yang Gaozhao, Zhao Xueshui, Xie Hongwei. Reliability experimental study of optical streak camera[J]. High Power Laser and Particle Beams, 2022, 34(2): 022001. doi: 10.11884/HPLPB202234.210382
[6]	Jiang Xiaoguo, Yang Xinglin, Jiang Wei, Jing Xiaobing, Chen Nan, Li Jin, Li Yuan, Wang Yuan, Liu Bangliang, Zang Zongyang, Chen Mao, Wang Yongwei. Technique study to improve radiographic-testing reliability basing on self-excitation of pulsed power system[J]. High Power Laser and Particle Beams, 2022, 34(6): 064006. doi: 10.11884/HPLPB202234.210133
[7]	Ma Chenggang, Li Hongtao, Deng Minghai, Cao Ningxiang, Mo Tengfu, Wang Xiao, Zhang Zhiqiang. Experimental research on reliability of 1 MV X-ray system for radiography[J]. High Power Laser and Particle Beams, 2020, 32(2): 025018. doi: 10.11884/HPLPB202032.190378
[8]	Tong Wei, Song Zhiquan, Fu Peng, Li Hua, Zhang Xiuqing, Wang Shusheng. Influence analysis of discharge branch on the reliability of quench protection system in CFETR[J]. High Power Laser and Particle Beams, 2019, 31(8): 086001. doi: 10.11884/HPLPB201931.190050
[9]	Zhao Juan, Li Bo, Li Xiqin, Cao Ningxiang, Huang Bin, Yu Zhiguo, Zhang Xin, Wang Lan, Li Hongtao. Design and actualization of high electromagnetic compatibility high power constant-current supply[J]. High Power Laser and Particle Beams, 2018, 30(2): 025007. doi: 10.11884/HPLPB201830.170359
[10]	Guo Fan, Jiang Wei, Yang Xinglin, Zhang Linwen. Integration of S7 programmable logic controller in EPICS[J]. High Power Laser and Particle Beams, 2017, 29(08): 085103. doi: 10.11884/HPLPB201729.170051
[11]	Zhu Lili, Huang Liansheng, Fu Peng, Gao Ge, Shen Jun, He Shiying, Wang Guanghong. Development of console system for EAST poloidal field power supply[J]. High Power Laser and Particle Beams, 2017, 29(04): 046002. doi: 10.11884/HPLPB201729.160438
[12]	Xu Weibin, Guo Yuhui, Zheng Yawei, Luo Bingfeng, Jia Huan. Design of synchronous controller for accelerator based on FPGA[J]. High Power Laser and Particle Beams, 2015, 27(01): 015101. doi: 10.11884/HPLPB201527.015101
[13]	Zhou Songqing, Guan Xiaowei, Zhang Shiqiang, Qu Pubo, Sun Yanhong, He Minbo. Application of GO methodology to reliability analysis in solid-state laser system[J]. High Power Laser and Particle Beams, 2014, 26(02): 021005. doi: 10.3788/HPLPB201426.021005
[14]	jia zhanqiang, cai jinyan, liang yuying, han chunhui. Reliability assessment of metallized film pulse capacitor[J]. High Power Laser and Particle Beams, 2011, 23(01): 0- .
[15]	song shihua, sheng peng, liu sheng, wang gensheng, zeng yan, hu chundong. Programmable logic controller system in neutral beam injector’s ion source test stand[J]. High Power Laser and Particle Beams, 2011, 23(06): 0- .
[16]	cong yan, wei baowen, xu zhe, wang xianwu, ren hongwen, wen lianghua, yi xiaoping. High reliability low level RF control system for HIRFL-CSRe[J]. High Power Laser and Particle Beams, 2010, 22(11): 0- .
[17]	chen guang-yu, yang dong, zhang xiao-min, he shao-bo, zheng wan-guo, you yong. Reliability analysis of Xe-flashlamps of disk amplifier subsystems for laser facility[J]. High Power Laser and Particle Beams, 2007, 19(07): 0- .
[18]	zhao jian-yin, sun quan, zhou jing-lun, he shao-bo, wei xiao-feng. Failure analysis of metallized film pulse capacitors based on accelerated degradation data[J]. High Power Laser and Particle Beams, 2006, 18(09): 0- .
[19]	zhao jian-yin, liu fang, sun quan, zhou jing-lun, wei xiao-feng, he shao-bo. Reliability assessment of metallized film capacitors using degradation failure model[J]. High Power Laser and Particle Beams, 2005, 17(07): 0- .
[20]	chen hao, xu zhou, jin xiao, li ming, shan li-jun, lu he-ping, yang xing-fan, deng ren-pei, zhang zhi-fu, liu xi-san. Spot size measurement of new type X-ray source designed[J]. High Power Laser and Particle Beams, 2004, 16(06): 0- .

Supplements(0)

Cited By

Cited by

Periodical cited type(9)

1.	任天佑，严宇，刘康凯，王路伽，祁江浩，王世卓. 适用于煤层瓦斯增透的高压脉冲放电关键技术研究. 电气防爆. 2024(01): 14-20 .
2.	刘毅，廖洪彬，程晋，李柳霞，林福昌，赵勇. 脉冲放电破岩等离子体通道长度预测方法. 强激光与粒子束. 2024(05): 151-159 . 本站查看
3.	郭军，米鑫程，冯国瑞，白锦文，文晓泽，朱林俊，王子，皇文博. 基于液电效应的高压电脉冲岩体致裂特征及机理. 煤炭学报. 2024(05): 2270-2282 .
4.	金玉静，王大庆，陆皓. GTAW自激发超声工艺对AISI 316不锈钢堆焊层的有效性分析. 热加工工艺. 2024(12): 133-138+144 .
5.	马宁，邓岳，凌雪，杨麟睿，钱阳，刘毅，黄仕杰. 高压脉冲放电在大直径扩底灌注桩中的应用技术研究. 钻探工程. 2024(06): 152-159 .
6.	赵景林，王志强，王进君，张东东，李国锋. 基于Kriging模型的水中放电沉积能量优化分析. 强激光与粒子束. 2023(03): 149-158 . 本站查看
7.	孙树强，王来东. 改进SPWM脉冲技术的多电平逆变器功率控制仿真. 计算机仿真. 2023(09): 66-69+75 .
8.	余庆，张辉，杨睿智. 基于LS-DYNA的液电效应冲击波数值模拟. 爆炸与冲击. 2022(02): 128-139 .
9.	康忠健，王聪，聂云良，邵在康，龚大建. 非常规储层电脉冲共振增产技术研究与应用. 强激光与粒子束. 2021(06): 82-87 . 本站查看